New 2012 Zed Audio Amps - Coming May 2012!

ZED AUDIO CORPORATION

To be introduced May 2012

MIKRO 1 MSRP $265 – Includes a remote
volume control module weight <3lbs

*Mono block 200w at 4 ohm/300w at 2 ohm
*RCA inputs x 2 balanced and will accept OEM radio direct
*High Pass crossover 12dB/octave Linkwitz 10Hz – 200Hz
*Low Pass crossover 24dB/octave Linkwitz 40Hz – 230Hz
*Bass boost at 40Hz 0 to +12dB of boost
*Level control 0.35v – 8.7v
*Remote level port using a 3.5mm jack socket (Space dictated the use of this socket)
*Turn on circuit automatically senses that if a trigger voltage is applied to the remote port, the signal and DC sensing circuits are locked off. If no trigger voltage is applied to the remote input, then turn in is accomplished by the signal or DC sensing circuit.
*Power supply is regulated and uses my dual rail technology for higher efficiency.
*When the heat sink temperature reaches 57 deg C the high rail is prevented from switching on.
*Full range class D design using all discrete circuits.
*211mm W x 135mm D x 41.8mm H (8.3”W x 5.3”D x 1.64”H)


MIKRO 4
MSRP $265 weight <3lbs

*4 channel rated at 60w x 4 at 4 ohm/80-90w x 4 at 2 ohm
*RCA inputs x 4 balanced and will accept OEM radio direct.
*Each channel pair has a 12dB/octave Butterworth State Variable crossover 45Hz-3.1KHz
*Selector switch per channel pair for FLAT, HIGH PASS or LOW PASS response
*Level control 0.35v – 8.7v per channel pair
*Turn on circuit automatically senses that if a trigger voltage is applied to the remote port, the signal and DC sensing circuits are locked off. If no trigger voltage is applied to the remote input, then turn in is accomplished by the signal or DC sensing circuit.
*Full range class D design using all discrete circuits.
*211mm W x 135mm D x 41.8mm H (8.3”W x 5.3”D x 1.64”H)

TRIDENT 1 MSRP $370 – Includes a remote volume control module

*Mono block 350w at 4 ohm/500w at 2 ohm
*RCA inputs x 2 balanced and will accept OEM radio direct
*RCA line outputs, 1 in phase for daisy chaining and 1 anti-phase for bridging 2 amps.
*High Pass crossover 24dB/octave Linkwitz 10Hz – 200Hz
*Low Pass crossover 24dB/octave Linkwitz 40Hz – 230Hz
*Phase shift control variable 0 – 180 degrees
*3 band equalizer at 25Hz, 40Hz and 63Hz boost and cut +/-12dB
*Remote level port. This port includes drive for power and clip LEDs.
*Level control 0.25v – 8.2v
*Differential drive from preamplifier to main amplifiers
*Selector switch for FLAT, FULL PREAMPLIFIER or SLAVE.
*Turn on circuit automatically senses that if a trigger voltage is applied to the remote port, the signal and DC sensing circuits are locked off. If no trigger voltage is applied to the remote input, then turn in is accomplished by the signal or DC sensing circuit.
*Power supply is regulated and uses my dual rail technology for higher efficiency.
*Full range class D design using all discrete circuits.
*417mm W x 203mm D x 52.5mm H (16.4”W x 8”D x 2.06”H)

TRIDENT 4 MSRP $370

*4 channel rated at 100w x 4 at 4 ohm/150w x 4 at 2 ohm
*RCA inputs x 4 balanced and will accept OEM radio direct.
*Channels 1+2 High Pass crossover 12dB/octave Linkwitz 55Hz-4KHz
*Channels 1+2 Low Pass crossover 12dB/octave Linkwitz 55Hz-4KHz
*Selector switch for FLAT, HIGH PASS or LOW/BAND PASS
*Selector switch for LOW or BAND PASS
*Level control 0.25v – 8.3v
*Differential drive from preamplifier to main amplifiers
*Channels 3+4 selector switch for 2 or 4 inputs
*Channels 3+4 High Pass crossover 12dB/octave Linkwitz 55Hz-4KHz
*Channels 3+4 Low Pass crossover 12dB/octave Linkwitz 55Hz-4KHz
*Bass Eq circuit at 40Hz 0 to +12dB in cascade with Low Pass crossover
*Selector switch for FLAT, HIGH PASS or LOW/BAND PASS
*Selector switch for LOW or BAND PASS
*Mono/Stereo switch allows channels 3+4 to run as sub woofer channels
*Level control 0.25v – 8.3v
*Differential drive from preamplifier to main amplifiers
*Turn on circuit automatically senses that if a trigger voltage is applied to the remote port, the signal and DC sensing circuits are locked off. If no trigger voltage is applied to the remote input, then turn in is accomplished by the signal or DC sensing circuit.
*Power supply is regulated.
*Full range class D design using all discrete circuits.
*417mm W x 203mm D x 52.5mm H (16.4”W x 8”D x 2.06”H)


TRIDENT
6 MSRP $425 – Includes a remote volume control module

*6 channel rated at 75w x 6 at 4 ohm/125w x 4 at 2 ohm, Chs 5+6 rated at 1 ohm
*RCA inputs x 6 balanced and will accept OEM radio direct.
*Channels 1+2 High Pass crossover 12dB/octave Linkwitz 55Hz-4KHz
*Selector switch for FLAT or HIGH PASS
*Level control 0.25v – 8.3v
*Differential drive from preamplifier to main amplifiers
*Channels 3+4 High Pass Crossover 20Hz – 1KHz 12dB/octave Linkwitz
*Channels 3+4 Low Pass Crossover 500Hz – 4KHz 12dB/octave Linkwitz
*Selector switch for FLAT, HIGH PASS or LOW/BAND PASS
*Selector switch for LOW or BAND PASS
*Level control 0.25v – 8.3v
*Differential drive from preamplifier to main amplifiers
*Channels 5+6 High Pass Crossover 10Hz-250Hz 12dB/octave Linkwitz
*Channels 5+6 Low Pass Crossover 40Hz – 230Hz 24dB/octave Linkwitz
*Stereo/Mono selector switch
*When the Stereo/Mono switch is in MONO then Ch’s 5+6 mixed to mono and the Bass Eq and the Remote Level Port are then in circuit
*Bass Eq control at 40Hz variable 0 - +12dB
*Remote level port. This port includes drive for power and clip LEDs.
*Level control 0.25v – 8.3v
*Differential drive from preamplifier to main amplifiers
*Channels 5+6 are rated to 1 ohm so can be bridged to 2 ohm
* Master input selector switch allows 2, 4 or 6 channel input selection.
* Position “6 in” means 6 inputs to 6 outputs.
* Position “4 in” means 1-4 inputs to 6 outputs where channel 5 receives the mix of channels 1+3 and channel 6 the mix of 2+4.
* Position “2 in” means input 1 feeds Chs 1, 3 and 5 and input 2 feeds Chs 2, 4 and 6.
*Turn on circuit automatically senses that if a trigger voltage is applied to the remote port, the signal and DC sensing circuits are locked off. If no trigger voltage is applied to the remote input, then turn in is accomplished by the signal or DC sensing circuit.
*Power supply is regulated.
*Full range class D design using all discrete circuits.
*417mm W x 203mm D x 52.5mm H (16.4”W x 8”D x 2.06”H)